Posts Tagged ‘cable’
January 29th, 2012 | 
Author: One of the most common questions I get from CCNA and CCNP candidates who are setting up their own home labs is “What cables will I need?” The answer is “It depends.” As you know from your exam studies, the physical layout of your lab is what determines the cables you’ll need. Let’s take a look at the most common home lab cable types and when you will need them.
Straight-through cables have quite a few uses in a CCNA / CCNP home lab. You’ll need them to connect a switch port to an AUI port on a router (and you’ll need a transceiver for that as well). If you have an ISDN simulator, straight-through cables can be used to connect a router’s BRI port to the simulator.
Read the rest of this entry »
Posted in 
One of the most common questions I get from CCNA and CCNP candidates who are setting up their own home labs is “What cables will I need?” The answer is “It depends.” As you know from your exam studies, the physical layout of your lab is what determines the cables you’ll need. Let’s take a look at the most common home lab cable types and when you will need them.
Straight-through cables have quite a few uses in a CCNA / CCNP home lab. You’ll need them to connect a switch port to an AUI port on a router (and you’ll need a transceiver for that as well). If you have an ISDN simulator, straight-through cables can be used to connect a router’s BRI port to the simulator.
Crossover cables are used to connect switches and allow them to trunk. If at all possible, get two switches in your home lab. This will allow you to gain valuable experience in manipulating root bridge election, working with STP, and creating EtherChannels.
Read the rest of this entry »
One of the most common questions I get from CCNA and CCNP candidates who are setting up their own home labs is “What cables will I need?” The answer is “It depends.” As you know from your exam studies, the physical layout of your lab is what determines the cables you’ll need. Let’s take a look at the most common home lab cable types and when you will need them.
Straight-through cables have quite a few uses in a CCNA / CCNP home lab. You’ll need them to connect a switch port to an AUI port on a router (and you’ll need a transceiver for that as well). If you have an ISDN simulator, straight-through cables can be used to connect a router’s BRI port to the simulator.
Crossover cables are used to connect switches and allow them to trunk. If at all possible, get two switches in your home lab. This will allow you to gain valuable experience in manipulating root bridge election, working with STP, and creating EtherChannels.
Read the rest of this entry »
As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we’ll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here’s part of a configuration from one of my access servers:
ip host FRS 2006 100.1.1.1
ip host SW2 2005 100.1.1.1
ip host SW1 2004 100.1.1.1
ip host R2 2002 100.1.1.1
ip host R1 2001 100.1.1.1
ip host R3 2003 100.1.1.1
interface Loopback0
ip address 100.1.1.1 255.255.255.255
no ip directed-broadcast
This is an IP Host table, and this is what makes the entire AS setup work. Your PC will connect to the access server, and the access server is in turn physically connected to your other routers and switches via an octal cable. One end of the octal cable splices off into eight separate cables, each terminated with an Rj-45 connector. That connector will be placed into the console port of one of your home lab devices. In this configuration, I have connector 1 connected to the console port of R1, connector 2 to R2, connector 3 to R3, connector 4 to Sw1, and so forth. (The connectors are physically numbered as well.)
The IP Host table entries here are linked to the loopback address shown. The loopback can be any address, but it must match the address in the IP Host table. This allows you to create reverse telnet sessions to the routers and switches.
To open the reverse telnet sessions upon opening a connection to the AS, type the entire name of the device and press the enter key twice. A connection to that device will now be visible, as shown here:
Read the rest of this entry »
