Posts Tagged ‘access’
June 22nd, 2011 | 
Author: As your CCNA / CCNP home lab expands, an access server such as the Cisco 2509 or 2511 is one of the best investments you can make. In this article, we’ll look at the basic configuration for an access server and discuss how to connect to the other routers and switches in your pod through the AS.
Here’s part of a configuration from one of my access servers:
ip host FRS 2006 100.1.1.1
ip host SW2 2005 100.1.1.1
ip host SW1 2004 100.1.1.1
ip host R2 2002 100.1.1.1
ip host R1 2001 100.1.1.1
ip host R3 2003 100.1.1.1
interface Loopback0
ip address 100.1.1.1 255.255.255.255
no ip directed-broadcast
This is an IP Host table, and this is what makes the entire AS setup work. Your PC will connect to the access server, and the access server is in turn physically connected to your other routers and switches via an octal cable. One end of the octal cable splices off into eight separate cables, each terminated with an Rj-45 connector. That connector will be placed into the console port of one of your home lab devices. In this configuration, I have connector 1 connected to the console port of R1, connector 2 to R2, connector 3 to R3, connector 4 to Sw1, and so forth. (The connectors are physically numbered as well.)
The IP Host table entries here are linked to the loopback address shown. The loopback can be any address, but it must match the address in the IP Host table. This allows you to create reverse telnet sessions to the routers and switches.
To open the reverse telnet sessions upon opening a connection to the AS, type the entire name of the device and press the enter key twice. A connection to that device will now be visible, as shown here:
Read the rest of this entry »
Posted in 
A Cisco home lab is an invaluable study tool when you’re preparing for CCNA and CCNP exam success. Once you’ve gotten a couple of routers and switches, you’ll quickly get tired of moving that blue console cable every time you want to configure a different device. The solution to this problem is purchasing and configuring an access server (AS).
For those of you new to access servers, note that these are not white boxes running Microsoft operating systems. These are Cisco routers that allow you to connect to all the routers and switches in your home lab without moving a cable. You can physically or logically connect to the access server and work with all your devices from there.
When you’re pricing access servers, please remember that you do NOT need an expensive AS. Right now on ebay there are access servers costing up to $5000 – this is NOT what you want to buy. What you’re looking for is something like a 2509 or 2511, which is going to run you anywhere from $100 – $200. It’s money well spent, because once you get an AS, you’ll really wonder how you ever did without it.
Read the rest of this entry »
Occasionally, during your CCNA and CCNP studies, you’ll run into a term that just doesn’t quite make sense to you. (Okay, more than occasionally!) One such term is “reverse telnet”. As a Cisco certification candidate, you know that telnet is simply a protocol that allows you to remotely connect to a networking device such as a router or switch. But what is “reverse telnet”, and why is it so important to a Cisco CCNA / CCNP home lab setup?
Where a telnet session is started by a remote user who wants to remotely control a router or switch, a reverse telnet session is started when the host device itself imitates the telnet session.
In a CCNA / CCNP home lab, reverse telnet is configured and used on the access server. The access server isn’t a white box server like most of us are used to; an access server is a Cisco router that allows you to connect to multiple routers and switches with one session without having to move a rollover cable from device to device.
Your access server will use an octal cable to connect to the other routers and switches in your home lab. The octal cable has one large serial connector that will connect to the access server, and eight rj-45 connectors that will connect to your other home lab devices. Your access server then needs an IP Host table in order to perform reverse telnet.
An IP Host table is easy to put together (and you better know how to write one to pass the CCNA!). The IP Host table is used for local name resolution, taking the place of a DNS server. A typical access server IP Host table looks like this:
Read the rest of this entry »
A CCNA or CCNP candidate who wants to be totally prepared for their exams is going to put together a home lab to practice on. With used Cisco routers and switches more affordable and plentiful then ever before, there’s really no excuse to not have one!
With the many different models available, there is some understandable confusion among future CCNAs and CCNPs about which routers to buy and which ones to avoid. You can take almost any set of Cisco routers and put together a home lab; part of the learning process is taking what equipment you have available and putting together your own lab! For those of you preparing to start your home lab or add to your existing one, this article will list the routers I use in my Cisco pods. You certainly don’t have to have all this equipment, but this will give you some good ideas on how to get started.
The most versatile router you can get for your CCNA / CCNP home lab is a 2520. These routers come with four serial ports, one ethernet port, and one BRI interface for ISDN practice. This mix of interfaces means you can actually use it as a frame relay switch while using the ethernet and BRI ports for routing. (There is no problem with using a lab router as both your frame relay switch and a practice router; for a frame relay switch sample configuration, visit my website!)
My pods consist of five routers and two switches, and three of the five routers are 2520s, due to their versatility. A recent ebay search showed these routers selling for $99 – $125, an outstanding value for the practice you’re going to get.
Read the rest of this entry »
